Ihr Warenkorb ist leer
Ihr Warenkorb ist leerProduktinformation
Keine Batterie enthalten
Welche Art von Batterie wird unterstützt?
803040 ist eine Polymerlithiumbatterie, das Maß ist 40mm*30mm*8mm, Standardspannung ist 3.7V und die volle Spannung ist 4.2V.
Charles Whitt
Bewertet in den USA am5. März 2024
Fits my Raspberry Pi Zero 2 W perfectly, the included hardware is perfect for the project case I have, standing off the UPS board about 1/4". The adhesive patch for the LiPo battery (not included) is a nice touch.As mentioned by John in his review, check the plug polarity of your battery against the UPS board (marked in + and -). The battery I bought had the wires reversed to the need of the board. I was able to pull up (gently) on the little white tabs in the photo and pull the wires out of the terminal, then reinserted them in the proper polarity.Double check the seating of the pogo pins before tightening your screws, and when you have it all together, you'll have a nice little battery backed up single board computer.
kekeke
Bewertet in Deutschland am 30. August 2024
Purchased this hat with the battery recommended by Amazon and nearly burned it right away because the polarity of the Hat and the battery were reversed. BE CAREFULhttps://www.amazon.de/-/en/Lithium-Polymer-Battery-Rechargeable-Connector/dp/B08FD39Y5R/ref=pd_bxgy_d_sccl_1/262-1080977-0692423?pd_rd_w=A9PPY&content-id=amzn1.sym.049d9fe5-326c-4463-9183-bdeeaea54956&pf_rd_p=049d9fe5-326c-4463-9183-bdeeaea54956&pf_rd_r=NV3BHM3YKSBD8N2PM1TM&pd_rd_wg=33Pay&pd_rd_r=b3a4a3a5-4da5-44be-a291-acbe017dd63d&pd_rd_i=B08FD39Y5R&psc=1Not an issue to the product, but amazon recommends a battery which does not fit into hat: the battery length is 51 mm, and there is only about 34 mm space available to fit inside. Be careful with that too.Beside that, everything seems to be working fine.
dcheeseman
Bewertet in den USA am15. Mai 2024
Arrived in what looked like good condition. I plugged in the 1000ma 803040 battery it recommended. Immediately got too hot to handle to the touch and I had to unplug the battery. Clearly something was internally shorted; switch was off and none of the pogo pins were bent into each other or anything like that. Assumed maybe it had to be assembled to avoid overheating but a) it overheated when fully assembled and b) to assemble it you need the battery plugged in ahead of time because the jst faces toward where the pi zero mounts. I was still able to test this because the through mounts for the battery connector weren't trimmed and I was able to 'plug' my battery into it with it fully assembled. Still no go and fast/dangerous overheating.TLDR: I got a defective product that had some internal short and was causing thermal runaway. UNSAFE. DO NOT BUY
JHoney
Bewertet in den USA am14. Oktober 2024
This still sticks with the micro USB connector which is unfortunate, but that's what RPi has done so at least it is consistent.The charge light blinks whenever the module is supplied power, even if there is no battery attached.I like that waveshare defines all the components used in the product images. I don't think I've seen that level of detail before on a product without going to the their wiki.It is a little fiddly to attach to the Pi. Once it is together it makes a solid little unit.If you mistakenly connect the battery in reverse the device gets super hot (80°C+). Nothing seems to have been damaged when I did that. Important to remember that there is no standard polarity for JST connector.Operation has been good. I put it with a 900mAh cell, Pi Zero W 1.1, and 2.13 e-Paper Hat v4 to make a pwnagotchi. I can get 3-4 hours per charge.
NicholasKrupa
Bewertet in den USA am31. März 2023
It works have been using it for a project for over a year now even the made battery monitoring script have no complaints thus far.
John
Bewertet in den USA am30. September 2023
WARNING!!!! Make sure to triple check the polarity before plugging in any batteries.I instantly fried this board because the positive/negative is reverse from all the PH2.0 batteries I have from flying drones and the 10000mAh battery I specifically purchased for my project. Waveshare did reach out to try and make things right, but I accept the fault for assuming.
Chris
Bewertet in Deutschland am 18. Juni 2022
Um mein e-Ink Display (auch Waveshare) autark ohne Stromversorgung zu betrieben, habe ich diesen UPS HAT für meinen Raspberry Pi Zero bestellt.Ist jetzt seit über 2 Monaten in Betrieb.Dieses Board, der Pi Zero und der e-Ink HAT haben die gleiche Größe und können gestapelt montiert werden.+ Funktioniert 100% wie beschrieben.+ Betrieb mit Akku und auch gleichzeitig mit Netzteil möglich+ Ladevorgang wird automatisch beendet, wenn Akku voll (kein permanentes Laden)+ Kapazität reicht für gut 20 Aktualisierungen meines e-Ink Displays (Es erzeugt einen Tagesplan mit Terminen, Wetterbericht und einem 3-Monatskalender. Wird dazu 1x pro Tag manuell für ca. 10 Minuten gestartet)+ Anleitung zum Auslesen und Berechnen des Akku-Ladezustands auf Website verfügbar.+ Plug&PlayBin sehr zufrieden. Funktioniert genau so wie ich es erwartet habe.Lieferzeit wie angegeben, Qualität 1A, Anleitungen und Code-Beispiele vorbildlich.
Produktempfehlungen
21.99€
10 .99 € 10.99€