Warenkorb

Ihr Warenkorb ist leer

Ihr Warenkorb ist leer

73 Werte 1460 Stück Widerstände Kit 1 Ohm-1 M Ohm, 1% Präzision, 1/4W Metallfilm widerständen Sortiment kompatibel mit Arduino für DIY Heimwerkerprojekte und Experimente

Kostenloser Versand ab 25.99€

15.99€

6 .99 6.99€

Auf Lager
  • ★【Hohe Qualität】:Widerstandstoleranz: ± 1%; Leistung: 1/4w. 1/4w Metallfilm und dickeren Metallstiften für eine bessere Verbindung, niedrigem Temperaturkoeffizienten und stabile Leistungsmerkmale, mit denen Sie die elektrischen Experimente schneller und reibungsloser abschließen können
  • ★【Anwendbar】:Das Widerstands-Sortiment kann auf Arduino-Projekte und andere elektronische und elektrische Experimente angewendet werden
  • ★【Einfach zu Bedienen】: Jeder Ohm-Widerstand einzeln verpackt und die zusätzliche Beschriftung jeder Sorte garantiert Ihnen höchsten Komfort - Kein langes Suchen notwendig für eine einfache Organisation, ohne Farbbänder zu lesen. Unser Widerstands-Sortiment-Kit mit verschiedenen Werten erfüllt alle Ihre Bedürfnisse
  • ★【Was Sie Bekommen】: 1/4W (0,25 Watt) Metallfilmwiderstands Sortiment Kit(Eine praktische Farbtabelle liegt dem Set bei) mit praktischer verpackung zum bequemen aufbewahren und verwenden
  • ★Dokumentation Link kann nicht angezeigt werden. Wenn Sie technische Dokumentation benötigen, klicken Sie bitte auf "Geekstory" (Sie finden "Sold by Geekstory" unter der Schaltfläche "Buy Now"), klicken Sie auf der neuen Seite auf "Ask a question", um eine E-Mail zu senden.



Helmut Schmidt
Bewertet in Deutschland am 6. Februar 2025
Gutes Sortiment. Schon im Einsatz.
Gerhard Harz
Bewertet in Deutschland am 7. April 2025
Sehr praktisch mit den Tütchen
M. Rux
Bewertet in Deutschland am 24. Juli 2024
Die Widerstände sind getrennt, nach Werten sortiert und in kleinen beschrifteten Beuteln verpackt.Eine aufklebbare Farbcodetabelle lag auch bei.
Scott Dawe
Bewertet in Kanada am 24. Mai 2024
Easy to read, organized and a great addition to my R/C hobby.
D., Rolf
Bewertet in Deutschland am 19. Januar 2024
Die Anschlussdrähte, mit 0,32 mm bis 0,36 mm, als "Thick Legs" zu bezeichnen, ist etwas weit her geholt. Marken-Widerstände haben da 0,6 mm. Die Toleranz mit 1% halten leider nicht alle Widerstände des Sortiments ein. Im schlechtesten Fall habe ich Abweichungen von 5% gemessen. Auch den Temperatur-Koeffizient würde ich nicht als "Low Temp Coefficient" bezeichnen, da ich eine Abweichung von mehr als 300ppm pro Kelvin gemessen habe. "Metallfilm"-Widerstände sollten da ehr bei 50ppm liegen.Zum Basteln auf einem Steckbrett oder Lochrasterplatine reichen sie aber aus.
D Simpson
Bewertet in Kanada am 9. Mai 2022
The leads are quite thin, so depending upon the state of your breadboard, the leads can be too loose or too flimsy to push in.If you are soldering, then they will work well.
Customer
Bewertet in Kanada am 11. August 2020
Parfait pour mes montages audio. Plus besoin de chercher les valeurs. Ménage un temps incroyable.
J. Epstein
Bewertet in den USA am28. Dezember 2019
A well-organized, complete selection within its range. Note that the largest value is 1Megohm - I need a few values between 1M and 10M and had to cover them separately.The resistor leads are thin but that is actually a convenience - two leads can fit in a single standard perfboard hole if needed. And they have held up just fine to bending, resoldering, etc so they are not flimsy at all.
Jamie M
Bewertet in den USA am26. Mai 2018
Great value and variety. I also love that they came with a band legend sticker. That will be useful to stick on the lid of the sorting tray they will go into. On the down side; The pouches were not in order, a few of them were mislabeled (but the stamp on the ribbon was correct), and some of them were labeled differently even within the same value range. (See pictures)BUT, those few complaints are fairly trivial when you start to test and use these items; testing a random smattering of the resistors shows that they do indeed fall nicely within the 1% range, which is really all that matters here. Random tests pictured.