Ihr Warenkorb ist leer
Ihr Warenkorb ist leerProduktinformation
TW
Bewertet in Deutschland am 31. März 2025
Wirklich ein top Resin. Klare Empfehlung. Man sieht den Unterschied in der Qualität der Drucke, verglichen mit den üblichen günstigeren.
Alberto
Bewertet in Spanien am 3. Februar 2025
Se supone que se lava al agua, no es asi. Al ver que no se lava al agua, he intentado hacer lo que recomienda el fabricante, usar una mezcla de ethanol+agua, dando ningun buen resultado. Al final me decidí por lavar solo con ethanol, tampoco dio resultado. Y no, no es falta de experiencia, llevo mas de 5 años usando impresoras de resina y con esta en concreto estoy teniendo recuerdos de mis primeros dias en este "hobby". Hay otras marcas que literalmente, bajo el grifo con agua tibia, se limpian y solo quedaría dejarlas secar tranquilamente encima de un paño seco. No la volvería a comprar, ni regalada vamos.
Leon74boy
Bewertet in Frankreich am 30. Oktober 2024
Comme d’hab la résine sirayatech reste incroyable quelque soit le model que vous choisissez
Tomzi
Bewertet in Deutschland am 11. Januar 2024
watter washable is kind of tricki statement. compared to other brand water washable this one does not really go off with just water. other properties are good. smell is not terrible. owerall it is OK.
O
Bewertet in Kanada am 5. September 2023
Incredible product. Had a few issues with settings on my printer but Siraya Tech Support was able to sort me out. 10/10 customer service.
Customer
Bewertet in Deutschland am 26. Juli 2023
The only issue I've had, was the provided Chitubox profile for this resin on my Elegoo Saturn 2 had too short of a layer time, causing fine-detailed parts to have repeated print failures.Otherwise it's a great product, with a mild smell when the hood is off the printer (it has an included activated charcoal filter inside).Cure-time seems rather long, and one of the details not mentioned in the description is the need to use a 15% IPA/85% water mixture for cleaning. You only read that on the SirayaTech website's spec sheet.But the resin is very liquid (at 24-25 degrees C), so you can also just let the print drip the excess and not have to worry too much about washing before curing.
Leon
Bewertet in Deutschland am 13. September 2023
Sowohl belichtung von 2.5 bis über 4 sekunden keine festigkeit der Supports, dadurch dann detailgrad grottig.Nie wieder ich geh wieder zum Anycubic Resin zurückPhoton Mono 2 falls interessant.
Cyrus F
Bewertet in Singapur am 10. August 2022
Die Medien konnten nicht geladen werden.
K. Skelton
Bewertet in den USA am9. Juli 2020
[EDIT Aug 24, 2020I have several prints from around the time of my initial review (July 8). For this test I printed 3 models with each resin mix: 100% Simple, Simple mixed with 30% Blu and mixed with 50% Blu. All were washed in 99% isopropyl alcohol, 20% iso and 35% vodka then rinsed with tap water and cured with a UV lamp. To date I've had zero issues with "melting" as others have reported. I used the same settings as I do for Blu (which come from the Anycubic Photon Google Sheet that is available in a number of enthusiasts groups).The 100% Simple is about as brittle as other standard resins, subjectively. The 50% mix was a little sticky after the wash/rinse for non-99% iso washes, and I didn't notice a significant difference in subjective toughness compared with the 30% mix. I did notice a marked increase in smell as I increased the quantity of Blu. ]I am a fan of the Siraya Blu and when I heard about Simple I had to find out if the low odor and clean up with 15% alcohol claims were true. I was too excited to try this and loaded up a model that has settings for Blu without really thinking about it, and Simple printed beautifully. I also found that the smell was hardly noticeable.I put the prints in my ultrasonic cleaner with an approx 20% IPA solution and cleaned them for three minutes. I was very pleased that there wasn't any obvious resin on the surface. Blu, on the other hand frequently felt gummy despite being cleaned with 99% IPA. While removing the supports they felt stiffer and more brittle than with Blu, but this resin isn't claiming to be tough.I'm going to try mixing this with Blu to see if it gains flexibility while retaining its low viscosity and easy clean up.
Produktempfehlungen