Ihr Warenkorb ist leer
Ihr Warenkorb ist leerSonnet Solo 10G Thunderbolt 3 zu SFP + 10 Gigabit Ethernet Adapter (SFP + [SR] enthalten).
Micha
Bewertet in Deutschland am 7. Januar 2025
Erfüllt Erwartungen komplett
Marvin
Bewertet in Deutschland am 13. März 2025
Sehr guter adapter hat mit allen SFP und SFP+ Transceivern, auch alle DAC Kabel haben funktioniert
Pascal
Bewertet in Frankreich am 21. November 2024
Fonctionne parfaitement avec Windows 11 et UDM Pro de Unifi. Vérifiez bien que votre PC est compatible thunderbolt 3 ou plus
Michael Schreiber
Bewertet in Deutschland am 16. Mai 2023
Funktioniert wie erwartet
BrixConsulting
Bewertet in Italien am 6. September 2022
Possiedo già l'altra versione, 10GbEthernet, e devo dire che le prestazioni sono pressoché identiche fra le due versioni. Cavo Thunderbolt un po corto ma adatto alla mia scrivania. Questa versione SFP+ scalda pochissimo. La versione 10GbE molto di più ma funziona sempre perfettamente.Un prodotto professionale e da consigliare assolutamente.
Jürgen Gigla
Bewertet in Deutschland am 19. Juni 2021
Ist super, aber es gibt vergleichbare, die günstiger sind
violentpanda
Bewertet in Deutschland am 14. September 2021
Hatte vorher den Solo 10G RJ45 Adapter... dieser ist mir über längere Nutzungsdauer zu heiß geworden und hat dann leider nicht mehr zuverlässig funktioniert. Das Problem besteht beim SFP+ Adapter nicht mehr - und falls dennoch benötigt, kann ich mit einem einfachen Slot-In Adapter wieder auf Kupferkabel adaptieren.Funktioniert am Macbook sowie iMac Pro einwandfrei.
Edoardo
Bewertet in Italien am 14. Mai 2021
Prodotto ben fatto. Su Mac funziona molto bene. Per ora nessun problema riscontrato.
M. G.
Bewertet in Deutschland am 11. Januar 2021
Betreibe das Gerät an einem Intel NUC mit ESXi 7 darauf. Die offiziellen Treiber können bei VMware heruntergeladen und dann einfach eingebunden werden. Nach einem Reboot und BIOS auf Legacy Thunderbolt, wird das Gerät angezeigt.Als Switch wird ein Ubiquiti UniFi 16-XG genutzt und ein beliebiges DAC Kabel (SFP+ Modul also herausgezogen und durch DAC ersetzt). Volle stabile 10G, was will man mehr.
starguardian
Bewertet in Deutschland am 8. Februar 2020
I have tested both versions of this Sonnet Solo10G ThunderBird 3 adapter (RJ45 vs. SFP+).The SFP+ version has better performance than the RJ45 and has no heat issue.Avoid the usage of 10GbE RJ45 modules for this TB3 adapter if possible or otherwise you will have the heat issue again.Use Twinax DAC cables upto 7.5m or OM4 fiber cables with fiber transceivers.The Sonnet Solo10G ThunderBird 3 RJ45 adapter version decreased the bandwith to avoid overheating or turned off completely.FreeNAS custom build shared storage for video editing (XEON 5680, 48GB RAM ECC, Mellanox ConnectX3 EN): 8x WD Red 4TB (RAIDZ2), L2ARC SanDisk 120GB Plus, ZIL/SLOG SanDisk 120GB PlusAFP: write: 448.2 MB/s, read: 890.6 MB/sSMB: write: 547.4 MB/s, read: 847.0 MB/sNFS: write: 125.1 MB/s, read: 789.6 MB/siSCSI: write: 135.8 MB/s, read: 771.7 MB/s
Dreagon Gilley
Bewertet in den USA am29. März 2020
For all of those that are saying the NIC gets hot and / or overheats...you unfortunately cannot beat physics. 10Gb NICs get hot by their nature.1. Small size2. Quietness3. AffordabilityPick 2 out of the 3 above. 3 out of 3 are impossible.You can have a small, affordable device with a tiny, whiny internal fan that will stay cool. You could have a small, affordable device with an intricate and expensive heat sink design but it would be expensive. You can have an affordable device with a cheaply made but giant metal heat sink that will stay cool.NOW, with that said, I want all 3 :). Luckily I'm an engineer, so this wasn't a challenge. I simply purchased the following 80mm fan for $11 and affixed it to the heat sink side of the housing:https://www.amazon.com/dp/B00G059G86/ref=cm_sw_em_r_mt_dp_U_nNoGEbTA4E9H6The design of the housing and the assembly is actually very well done from a thermal management perspective.I disassembled the unit and verified that the ribbed side of the housing is thermally connected to the controller. From the factory they applied thermal interface material to the controller and created a raised area in the housing to make contact with the TIM. They also placed a thermal pad on a secondary SMD. I replaced the TIM with higher quality since I had it open anyway and replaced the pad with a fujipoly of the same size. That was totally unnecessary, but I figured why not since I had it open anyway.Now the unit stays warm to the touch at best with the fan on the lowest setting.Yes, you can buy another brand of external NIC for the same price that already has a fan, but they sound like jet engines. My solution, while ugly lol, is very effective while remaining quiet.
Jesus luna
Bewertet in Mexiko am 26. Mai 2020
Todo muy bien! Impecable!
Produktempfehlungen
