Warenkorb

Ihr Warenkorb ist leer

Ihr Warenkorb ist leer

Waveshare Universal e-Paper Driver HAT Supports Various Waveshare SPI E-Paper Raw Panels Compatible with Raspberry Pi and Jetson Nano

Kostenloser Versand ab 25.99€

14.99€

6 .99 6.99€

Auf Lager
  • Universal e-Paper Driver HAT, supports various Waveshare SPI e-Paper raw panels
  • This is a universal driver board for e-Paper raw panels, can be used to drive various SPI interface e-Paper from Waveshare.
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUs
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)


Universal e-Paper Driver HAT, supports various Waveshare SPI e-Paper raw panels
Overview
This is a universal driver board for e-Paper raw panels, can be used to drive various SPI interface e-Paper from Waveshare.
Features
Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
Onboard voltage translator, compatible with 3.3V/5V MCUs
Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)
Specifications
Operating voltage: 3.3V~5V
Interface: 3-wire SPI, 4-wire SPI
Outline dimension: 65mm × 30.2mm
Mounting hole size: 3.0mm
Development Resources
Wiki : www.waveshare.com/wiki/e-Paper_Driver_HAT?amazon
Package Content
e-Paper Driver HAT x1
RPi screws pack (2pcs) x1
PH2.0 20cm 8Pin x1


Alexandru MARIN
Bewertet in Deutschland am 18. Februar 2025
Nice for an epaper project
Average Canadian Shopper
Bewertet in Kanada am 8. August 2024
A very good hat for raspberry pi from stop. Great for DIY projects. If you have eating screens. It allows you to use any eating screen with your raspberry pi four or five. Overall a fun item to use for DIY projects.
D.
Bewertet in Kanada am 6. Juni 2024
There’s a design bug with v3 boards. There is a pin that when set to hi enables the voltage regulators that go off to the epaper board ✅The 3.3v power is also sent to the enable pin OE on the 3.3 to 5v logic translator chip for the RPI and that bus becomes active ✅. This is great for a PI board.But for those who want to use the loose wires it’s not good (aka esp32-firebeatle etc). Powering up the epaper enables the translator bus and that fights the signals you’re trying to assert on the loose wires. Bus wars. Verified by a scope. Wired signal get pulled up or down.OE pin on the 3/5 translator chip should have went to the RPI to detect the presence of a PI and not that the epaper has power☹️You will be forced to buy the wave share ESP32 driver board…. But that sucks 1mA idle, good luck making a battery operated weather station or clock with that power hog. Fire beatle won’t work… pin drive too weak to fight the bus.
T
Bewertet in den USA am5. Oktober 2024
Works great with my 1.54" and 2.13" e-ink displays. Makes it a breeze to connect my e-ink displays to my microcontrollers. Comes with a 9pin cable and mounting hardware too, very nice! Definitely a project-ready driver.
S. Wellborn
Bewertet in den USA am27. Oktober 2024
If you have a Pi and an epaper panel without a driver, then get this. It works great. It just works right out of the box.
G. Watts
Bewertet in Großbritannien am 24. Dezember 2024
Despite the product title, this is not a universal adapter. Will only fit displays that have a 24-pin flat cable connector, The display I was wanting it for has 50-pins
Ein Augsburger
Bewertet in Deutschland am 20. Juli 2019
Da mein altes kaputt ging, habe ich dieses als Ersatz bestellt. Tut was es soll
Produktempfehlungen

7.48€

2 .99 2.99€

4.6
Option wählen

21.85€

9 .99 9.99€

5.0
Option wählen